半纤维素基阿维菌素载药微囊的制备及性能

目前阿维菌素以高效性、无污染和低抗药性等特点而得到广泛应用，但是其稳定性较差，易降解导致使用量较大从而造成浪费。为解决上述问题，本文以半纤维素为基体，利用原位聚合法制备阿维菌素载药微囊（HDCM），通过制备条件、热降解性、储存稳定性和释放动力学研究，确定了HDCM的载药量、热稳定性及释放性能。结果表明，在芯壁比为1∶34（质量比），温度为65℃，pH为3.5的制备条件下，HDCM的载药量可达66.5%，粒径较小且分散均匀。HDCM的热降解性能和恒温热稳定性能较阿维菌素原药有所提高，最高热分解温度从261℃增加到272℃，阿维菌素原药10h后降解率达到12.1%，而载药量为66.5%的HDCM降解率仅为5.2%。HDCM的释放机理满足Fick扩散，阿维菌素原药在水中的累积释放率在12h之内达到83.8%，而HDCM的累积释放率在24h之后才有所增大，12h内其释放率仅为33.7%，表明HDCM具有极好的缓释性能。     

MoS2-mesoporous LaFeO3 hybrid photocatalyst: Highly efficient visible-light driven photocatalyst

Perovskite type materials have high potential photocatalytic application towards both hydrogen energy generation and organic dye degradation due to their high stability and good reusability. Here, it is the first analysis of photocatalytic degradation of RhB and hydrogen energy evolution under visible light over MoS₂/LaFeO₃ nanocomposite. The physicochemical properties of the materials were characterized using a range of techniques such as XRD, TEM, XPS, FTIR, PL, photocurrent, etc. The optical properties of the nanocomposite show good absorption in UV-Vis spectra as compared to the bare LaFeO₃. In this study, MoS₂/LaFeO₃ nanocomposite was synthesized through single step in situ hydrothermal processes with a narrow bandgap, enhanced photocatalytic application under visible light. This novel MoS₂/LaFeO₃ nanocomposite is an efficient and promising photocatalyst for both hydrogen energy evolution and organic dye degradation.     

Failure mechanism of rigid polyurethane foam under high temperature vibration condition by experimental and finite element method

The failure mechanism of rigid polyurethane foam (RPUF) under room temperature (RT) and high temperature vibration conditions was investigated by experiment and finite element stimulation. Damaged RPUF specimens were prepared at different vibration amplitudes ranging from 0 to 19.879 mm at RT and 150 °C for different vibration times. The tensile test was utilized to evaluate the vibration damage degree of RPUFs, and the results exhibited that tensile strength decreased gradually with the increase of vibration amplitude and time at both RT and 150 °C. Thermogravimetric analysis and Fourier transform infrared spectroscopy illustrated that thermal degradation of RPUF is attributed to the decomposition of carbonyl urethane groups at 150 °C. The scanning electron microscopy analysis of the tensile fracture surfaces revealed that the vibration failure of RPUF mainly resulted from the existence of microcracks in cell structure. A finite element simulation was established by ABAQUS to study stress distribution of RPUF under different vibration loads, which then demonstrated that the microcracks are most likely to exist on the junction of two microcell units, which is due to convergence of stress in the process of vibration. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48343.     

木质素化学降解及其在聚合物材料中应用的研究进展

木质素是自然界储量丰富的可再生天然酚类高分子，可替代传统化石资源应用于聚合物材料合成。木质素分子结构中的大分子刚性骨架可赋予材料独特的力学性能和热稳定性。但木质素化学组成和分子结构复杂、反应活性低，限制了在聚合物材料领域的应用。化学降解是一种高效、高选择性且应用广泛的降解方法，经化学降解处理得到的木质素低聚物具有活性官能团多、反应活性高、溶解性好等优点，有利于拓展木质素在聚合物材料领域的高附加值应用。重点综述了近年来国内外有关木质素化学降解及其降解产物应用于聚合物材料的研究进展。     

Photocatalytic degradation and heat reflectance recovery of waterborne acrylic polymer/ZnO nanocomposite coating

This work aims to clarify the photocatalytic degradation mechanism and heat reflectance recovery performance of waterborne acrylic polymer/ZnO nanocomposite coating. To fabricate the nanocomposite coating, ZnO nanoparticles (nano-ZnO) were dispersed into acrylic polymer matrix at the various concentrations from 1 to 6% (by total weight of resin solids). The photocatalytic degradation of nanocomposite coating under ultraviolet (UV) light irradiation has been investigated by monitoring its weight loss and chemical/microstructural/morphological changes. As the topcoat layer, its heat reflectance recovery has been evaluated under UV/condensation exposure by using an artificial dirty mixture of 85 wt% nanoclay, 10 wt% silica particles (1–5 μm), 1 wt% carbon black, and 2 wt% engine oil. After 108-cycle UV/condensation exposure, infrared spectra and weight loss analysis indicated that the maximal degradation for nanocomposite coating is observed at 1 wt% nano-ZnO. On the other hand, after 96 hr of UV light exposure, the nanocomposite coating with1 wt% nano-ZnO could restore effectively the reflective index of solar-heat reflectance coating (from 58.45 to 80.78%). Finally, the photodegradation mechanism of this waterborne acrylic polymer coating has been proposed as the UV-induced formation of CC CO conjugated double bonds. As a result, its self-cleaning phenomenon can be achieved as the recovery of heat reflectance.     

A comparative study of photocatalytically active nanocrystalline tetragonal zyrcon-type and monoclinic scheelite-type bismuth vanadate

Monoclinic scheelite-type BiVO₄ is currently considered as one of the most promising non-titania photocatalysts, wheras tetragonal zircon-type BiVO₄ is still poorly understood. Herein, a new and simple synthetic approach was applied and nanostructured single-phase zircon-type BiVO₄ was successfully prepared by a controllable ethylene-glycol colloidal route. In addition, nanostructured monoclinic scheelite-type BiVO₄ powders were also fabricated through annealing of the as-prepared samples. A comparative study of the two BiVO₄ polymorphs was conducted and it turned out that the novel synthetic approach had a significant impact on porosity and photocatalytic performance of zircon-structured BiVO₄. All the prepared materials, as-prepared and annealed, were mesoporous, while measured values of specific surface area of some zircon-structured samples (～34?m²/g) were ～7 times higher than those reported thus far for this phase. Interestingly, for the first time, zircon-type BiVO₄, previously considered to be a poor photocatalyst, exhibited a better overall performance in degradation of methyl orange compared to monoclinic scheelite-type BiVO₄. Hence, it could be expected that the here-presented synthesis and observations will both arouse interest in scarcely studied tetragonal zircon-type BiVO₄ and facilitate as well as speed up further research of its properties.     

Chemistry of SiNx thin film deposited by plasma-enhanced atomic layer deposition using di-isopropylaminosilane (DIPAS) and N2 plasma

Silicon nitride (Si₃N₄) films have received great attention not only as dielectric materials for the gate dielectric of transistors and the insulator of capacitors, but also as a buffer layer and etch-stop layer for the semiconductor industry. As the applications of Si₃N₄ film increase, the necessity of investigating a novel deposition process applicable at low temperature has emerged. In this regard, the plasma-enhanced atomic layer deposition (PEALD) technique is attractive as a promising process; however, the Si₃N₄ film deposition process at growth temperatures less than 150?°C using PEALD has not been investigated. In this work, the growth behavior and chemistry of SiN_x (x?<?1.33) film deposited by the PEALD process at various growth temperatures were developed. Insufficient thermal energy from low growth temperature induces an unstable chemical state of deposited film due to the remaining unreacted ligand of adsorbed precursors. This state results in a further chemical reaction to SiO₂ formation by air exposure. Other chemical effects depending on chemical composition and electrical property were also examined in detail.     

Long term stability of electrocaloric response in barium zirconate titanate

The stability of the electrocaloric effect under electric field cycling is an important consideration in the development of solid-state cooling devices. Here we report measurements carried out on Ba(Zr_0.2Ti_0.8)O₃ ceramics which reveal that the adiabatic temperature change, polarization-electric field hysteresis loops and dielectric permittivity/loss show stable behavior up to 10⁵ cycles. We further demonstrate that the loss in electrocaloric response observed after 10⁵ cycles is associated with the migration of oxygen vacancies. As a result, the electrical properties of the material are changed leading to an increase in leakage current and Joule heating. Reversing the polarity of the electric field after every 10⁵ cycles changes the migration direction of oxygen vacancies, thereby preventing charge accumulation at grain boundaries and electrodes. By doing so, the electrocaloric stability is improved and the adiabatic temperature remains constant even after 10⁶ cycles, much higher than achieved in commercially available barium titanate ceramics.     

Hydrolytic degradation of poly(l‐lactic acid)/poly(methyl methacrylate) blends

The hydrolytic degradation of poly(l ‐lactic acid)/poly(methyl methacrylate) (PLLA/PMMA) blends was carried out by the immersion of thin films in buffer solutions (pH = 7.24) in a shaking water bath at 60 °C for 38 days. The PLA/PMMA blends (0/100; 30/70; 50/50; 70/30; 100/0) were obtained by melt blending using a Brabender internal mixer and shaped into thin films of about 150 µm in thickness. Considering that PMMA does not undergo hydrolytic degradation, that of PLLA was followed via evolution of PLA molecular weight (recorded by size exclusion chromatography), thermal parameters (differential scanning calorimetry (DSC)) and morphology of the films (scanning transmission electron microscopy). The results reveal a completely different degradation pathway of the blends depending on the polymethacrylate/polyester weight ratio. DSC data suggest that, during hydrolysis at higher PMMA content, the polyester amorphous chains, more sensitive to water, are degraded before being able to crystallize, while at higher PLLA content, the crystallization is favoured leading to a sample more resistant to hydrolysis. In other words, and quite unexpectedly, increasing the content of water‐sensitive PLLA in the PLLA/PMMA blends does not mean de facto faster hydrolytic degradation of the resulting materials. © 2018 Society of Chemical Industry